info on F Dick steels
info on F Dick steels
Would like to get information on these old F. Dick sharpening steels I recently bought. The arrows go in a different direction, I have heard the the arrow pointed toward the handle is the oldest one and the arrow pointed toward the tip a little more recent made. Also the one has "made in Germany US Zone stamped on it, which I assume had to be made after WWII?. They are both 14" steels plus the handle.
If it ain't broke, don't fix it!
Re: info on F Dick steels
Nice steels, Terry. Apparently the F. Dick stamp is pretty desirable.
I wasn't aware of the arrow designation. Interesting, for sure.
I have two, in 14 inch and 10 inch. The 14 inch steel is pretty neat with a flattened oval pattern for the blade.
I wasn't aware of the arrow designation. Interesting, for sure.
I have two, in 14 inch and 10 inch. The 14 inch steel is pretty neat with a flattened oval pattern for the blade.
Joe
Re: info on F Dick steels
means made between 1945 -1952. I do not know about the arrows. F.Dick still in business. I have a knife slick with a orange plastic handle. meaning no lines or roughness. Just re-aligns the wire edge.terryl308 wrote:Would like to get information on these old F. Dick sharpening steels I recently bought. The arrows go in a different direction, I have heard the the arrow pointed toward the handle is the oldest one and the arrow pointed toward the tip a little more recent made. Also the one has "made in Germany US Zone stamped on it, which I assume had to be made after WWII?. They are both 14" steels plus the handle.
Re: info on F Dick steels
found this info. There's a few guys at work with pre war (WW2) f dick steels,(the arrow points to the handle instead of to the tip of the steel) getting pretty rare these days but shows the quality.
Re: info on F Dick steels
some of mine. mainly Garage sale finds.mrwatch wrote:found this info. There's a few guys at work with pre war (WW2) f dick steels,(the arrow points to the handle instead of to the tip of the steel) getting pretty rare these days but shows the quality.
KNIFE STEELS
Gotham Cutlery
F. Dick smooth surface orange handle both for 1.50
Wilson, cast steel With a maker's stamp bearing their barleycorn and diamond
hallmarks, it reads, "I. WILSON, SYCAMORE ST., SHEFFIELD, ENGLAND.".
Unmarked in kitchen drawer black handle with the Remington set.
Black Bakelite handle .50
J. A. HENCKELS 1.00
Jewelstik Diamond 1.00
CASE XX SHEFFIELD ENGLAND
WUSTHOF DREIZACK HARTVE CHROME 1.00
Re: info on F Dick steels
Here's an older deluxe F Dick steel with fancy nickel trim and a fine carved horn handle. Still works well I use it often on my kitchen knives which are mostly Henkels Germany knives.
Re: info on F Dick steels
Here are two I have. 20" OAL (14" steel) and 13" OAL without the rings. The larger is an oval profile steel.
If I have seen further it is by standing on the shoulders of giants.
Wayne
Please visit My AAPK store https://www.allaboutpocketknives.com/catalog/btrwtr
Wayne
Please visit My AAPK store https://www.allaboutpocketknives.com/catalog/btrwtr
Re: info on F Dick steels
I always liked the "flat" steels but have never found a nice antique Dick one in usable condition. I have several steels I use but the horn handled Dick gets the most use, maybe because it has a finer cut than my LF&C or Henkels steels.
Re: info on F Dick steels
Thanks for all the responses, interesting subject. I used a F. Dick hog skinner back in the 50's and 60's great old blade. I'm still confused about my old one that I understand it a pre war (arrow toward the handle) but has "made in 'germany U.S. Zone under the arrow and F.dick stamping. Don't believe there was a "US Zone" prior to WWII. Maybe it's a "transition" model using the old arrow stamp.? I'll send a little better photo.
If it ain't broke, don't fix it!
Re: info on F Dick steels
Gunsil, I really like your carved horn steel, does the arrow point toward the handle, can't quite read it. I assume that is a pre war model. really nice. Terry
If it ain't broke, don't fix it!
Re: info on F Dick steels
Thanks, Joe and Terry!! The arrow points to the handle and the steel is 14" long plus the handle. It is marked Made in Germany so I think it is likely circa WW1 since the term Germany was not used a lot before then. Could be earlier but Prussia was often used for that part of the world before 1900. Terry, I had never heard about the arrow orientation for dating these but yours has to have been made post war by the "US Zone" marks.
Re: info on F Dick steels
I forgot about this one. 11" blade.
How about a sideways arrow time frame?
How about a sideways arrow time frame?
Joe
Re: info on F Dick steels
FRJ, Very nice looking flat steel, I've never had one but have seen photos of them, I assume it is a newer production, but that's just a guess. I am going to try and get some info from F.Dick on the history of their steels, if they respond I will post what I find out. Terry
If it ain't broke, don't fix it!
Re: info on F Dick steels
I didn’t even know about flat steels! It’s no wonder I haven’t been known as a sharpening savant.
Thanks guys and especially Terry for this thread.Brings back fond memories. If anyone has any of those GEC 15’s , you may remember the stories of my younger days at the Butcher Shop. I don’t remember how, but the tip is broken on this one from the shop.
Thanks guys and especially Terry for this thread.Brings back fond memories. If anyone has any of those GEC 15’s , you may remember the stories of my younger days at the Butcher Shop. I don’t remember how, but the tip is broken on this one from the shop.
I buy roosters combs and farmers..........................................................jack knives [/b]
GEC SFOs and others at LICK CREEK CUTLERY- www.allaboutpocketknives.com/wlf
May the Father and Son bless
Lyle
GEC SFOs and others at LICK CREEK CUTLERY- www.allaboutpocketknives.com/wlf
May the Father and Son bless
Lyle
Re: info on F Dick steels
Wlf, a little off topic, but we used to use the steels for tightening up the nut on the outter ring of our meat grinder.. maybe your steel got broken doing that? since steels are very hard they might also be brittle, just a guess however, Terry
If it ain't broke, don't fix it!
Re: info on F Dick steels
Were they stamping steel back in the 40s or are even the cheaper looking knives forged? I found a filet knife that seems like an interesting restoration project.