Page 1 of 1
Edge Company kit issue
Posted: Thu Jul 31, 2025 12:29 am
by prober996
I have a 1980s vintage (I think) Model 120 switchblade kit with blue scales that I cannot assemble. Try as I may, I can't get the spring to slide into position as per the instruction sheet. I don't know if the spring is malformed, or my brain is, but I am stumped. I have no idea of the value of this kit. If anyone is interested in taking a crack at such a project, message me with an offer. I can put it in my AAPK store.
Re: Edge Company kit issue
Posted: Thu Jul 31, 2025 5:28 pm
by XBMX
Send it to Bill DeShivs he''ll knock it right out and triple it's value.
Re: Edge Company kit issue
Posted: Fri Aug 01, 2025 11:25 pm
by prober996
XBMX wrote: ↑Thu Jul 31, 2025 5:28 pm
Send it to Bill DeShivs he''ll knock it right out and triple it's value.
I’m Bill could do the job, but I have no idea of the present value or its future value if it was assembled. It may not be worth the labor cost.
Re: Edge Company kit issue
Posted: Sat Aug 02, 2025 12:32 am
by Killgar
Looking at the "sold" prices of several EDGECO stiletto switchblades like yours over the past few years, I'd say a completed knife goes from $135-$145. In comparison, brand-new Frank Beltrame 9" switchblades cost about the same. So it doesn't look to me like people are willing to pay any kind of premium for an old EDGECO switchblade.
An unmade EDGECO stiletto kit sold here at AAPK for $175.
.
Re: Edge Company kit issue
Posted: Sat Aug 02, 2025 1:48 pm
by prober996
Killgar wrote: ↑Sat Aug 02, 2025 12:32 am
Looking at the "sold" prices of several EDGECO stiletto switchblades like yours over the past few years, I'd say a completed knife goes from $135-$145. In comparison, brand-new Frank Beltrame 9" switchblades cost about the same. So it doesn't look to me like people are willing to pay any kind of premium for an old EDGECO switchblade.
An unmade EDGECO stiletto kit sold here at AAPK for $175.
.
Interesting… it may be worth more as a kit than assembled. Thanks for the info Killgar.
Re: Edge Company kit issue
Posted: Sat Aug 02, 2025 2:08 pm
by Killgar
prober996 wrote: ↑Sat Aug 02, 2025 1:48 pm
Interesting… it may be worth more as a kit than assembled. Thanks for the info Killgar.
You're welcome.
I've seen other people have difficulty installing the spring. Sometimes the spring needs a little bending or filing to get the pin through. So if someone is a little crafty, and doesn't mind a little work, they shouldn't have a problem putting it all together.
Also, I noticed awhile ago that the old EDGECO stiletto spring, and the springs from the Frank Beltrame "Switch" line, are very similar, and might be the exact same. Since both knives were sold by Frank Beltrame, that wouldn't be a surprise.
So if a person ever needed a replacement spring for their EDGECO stiletto, and couldn't find someone to sell them a loose one, they might find someone with a broken "Switch" stiletto to sell and try cannibalizing the spring. I don't doubt that there are many people with broken "Switch" knives, because they are pretty cheap and the cast zinc liners are prone to breakage.
EDGECO spring on the left, Switch spring on the right.
Re: Edge Company kit issue
Posted: Sat Aug 02, 2025 2:42 pm
by prober996
Killgar wrote: ↑Sat Aug 02, 2025 2:08 pm
prober996 wrote: ↑Sat Aug 02, 2025 1:48 pm
Interesting… it may be worth more as a kit than assembled. Thanks for the info Killgar.
You're welcome.
I've seen other people have difficulty installing the spring. Sometimes the spring needs a little bending or filing to get the pin through. So if someone is a little crafty, and doesn't mind a little work, they shouldn't have a problem putting it all together.
Also, I noticed awhile ago that the old EDGECO stiletto spring, and the springs from the Frank Beltrame "Switch" line, are very similar, and might be the exact same. Since both knives were sold by Frank Beltrame, that wouldn't be a surprise.
So if a person ever needed a replacement spring for their EDGECO stiletto, and couldn't find someone to sell them a loose one, they might find someone with a broken "Switch" stiletto to sell and try cannibalizing the spring. I don't doubt that there are many people with broken "Switch" knives, because they are pretty cheap and the cast zinc liners are prone to breakage.
EDGECO spring on the left, Switch spring on the right.
Thanks again Killgar. Based on your great info, I think I will give it another try, and if I fail I’ll put this in my AAPK store and give someone else a crack at it.
Re: Edge Company kit issue
Posted: Fri Aug 08, 2025 2:18 am
by Madmarco
Killgar wrote: ↑Sat Aug 02, 2025 2:08 pm
prober996 wrote: ↑Sat Aug 02, 2025 1:48 pm
Interesting… it may be worth more as a kit than assembled. Thanks for the info Killgar.
You're welcome.
I've seen other people have difficulty installing the spring. Sometimes the spring needs a little bending or filing to get the pin through. So if someone is a little crafty, and doesn't mind a little work, they shouldn't have a problem putting it all together.
Also, I noticed awhile ago that the old EDGECO stiletto spring, and the springs from the Frank Beltrame "Switch" line, are very similar, and might be the exact same. Since both knives were sold by Frank Beltrame, that wouldn't be a surprise.
So if a person ever needed a replacement spring for their EDGECO stiletto, and couldn't find someone to sell them a loose one, they might find someone with a broken "Switch" stiletto to sell and try cannibalizing the spring. I don't doubt that there are many people with broken "Switch" knives, because they are pretty cheap and the cast zinc liners are prone to breakage.
EDGECO spring on the left, Switch spring on the right.
X-cellent and informative tutorial, buddy, as usual, thx!
Re: Edge Company kit issue
Posted: Fri Aug 08, 2025 5:19 am
by Killgar
Madmarco wrote: ↑Fri Aug 08, 2025 2:18 am
X-cellent and informative tutorial, buddy, as usual, thx!
Happy to help
.
.