Page 1 of 1

clip blade clicks on liner when opening

Posted: Fri Oct 26, 2012 1:54 am
by brax71
I picked up a kutmaster branded stockman a couple weeks back. As I just start to open the clip blade the slight sideways pressure from my nail in the nick pushes the blade against the liner and as it clears the brass of the liner, the blade audibly clicks as it slides sideways.
At first i thought the blade might just be bent, but without really 'going to town,' i wasn't able to bend it enough to keep it from clicking.
I also tried tapping the pin, thinking that maybe the blade was just too loose -- no dice there either.
Any other ideas? thanks!!

Re: clip blade clicks on liner when opening

Posted: Fri Oct 26, 2012 9:31 am
by Chief RID
Pretty confusing without a picture. I looked at my stockmans, I do not have a Kutmaster, and all mine push away from the liner when using the thumbnail to open. does it hit the liner when closing?

Re: clip blade clicks on liner when opening

Posted: Fri Oct 26, 2012 11:27 am
by TripleF
Return it.
Unfortunately, Utica/Kutmaster's quality isn't what you receive in other knives.

Re: clip blade clicks on liner when opening

Posted: Fri Oct 26, 2012 12:43 pm
by jerryd6818
brax71 -- Welcome to AAPK. Glad to have you aboard.


Is your Kutmaster Stockman an older one like this?
Utica Kutmaster StockmanM.JPG

Or a newer one, similar to this?
Utica Premium Stockmanm.JPG

Re: clip blade clicks on liner when opening

Posted: Fri Oct 26, 2012 11:44 pm
by brax71
jerryd6818,
mine's styled more like the older one but no shield on the scale and the tang stamp is different (the "usa" is left justified and has a "0" or an "O" to the right), and the blades 'look' like stainless vice carbon, although it's not marked as such.
The detail on the spey blade is very similar to the older which is looks a little different than most of my other stockman knives (stockmen?)

Chief RID,
i know it's a goofy description, sorry about that -- it doesn't rub on/click over the liner nearest the scale, rather the inner one separating the clip from sheepsfoot blades. it does not catch on the liner when closing... just from the sideways pressure when opening. there doesn't seem to be any damage to the edge indicating past interference, either.

thanks,
Andy

Re: clip blade clicks on liner when opening

Posted: Sat Oct 27, 2012 5:08 am
by Chief RID
Do any of the blades have any wobble when open?

Re: clip blade clicks on liner when opening

Posted: Sat Oct 27, 2012 4:46 pm
by orvet
If I understand the problem; the blade rubs the liner when you try to open it.
As you push a thumb nail into the nail nick the blade move sideways and rubs, but after it is opened it does not rub the liner when the blade closes.
Am I understanding the problem correctly?

If I understood the problem; I would ask Chief Rid's question: do that blade wobble when it is open?
If it does the most likely solution is to tighten the blade.

I have seen knives without blade wobble that will rub the liner (or other blades) when opening.
When I have seen this is was due usually to a longer & flexible blade. In that case there was no problem, just that the blade had more flex than it had room to move in the pocket of the frame.

Hope this helps.

Re: clip blade clicks on liner when opening

Posted: Sat Oct 27, 2012 6:33 pm
by muskrat man
blade flex or loose blade if neither of those you're out of luck. This is a common problem on boker 2020 folding hunters, a solid center liner will eliminate the clicking if the design allows the use of a full center liner but it may still rub.

Re: clip blade clicks on liner when opening

Posted: Thu Nov 01, 2012 2:53 am
by brax71
Thanks to all for the input -- since there does not seem to be any wobble when the blade is open, i reckon i'll get used to the click. I really appreciate everyone's responses!
Andy